3000kw Coal gas gasifier plant gasification power plant generator
The basic principle of coal gasification system is to convert coal into combustible gas. It is then used as fuel in gas engine to generate electricity. Coal gasification system is characteristic of small land requirement and environment friendly.
Our coal gasification process includes three steps. The First step is coal gasification, which convert coal into syngas. The Second step is syngas purification. The producer gas coming from gasifier usually contains contaminants including dust, coke, tar and etc. The contaminants will be removed by the purification system to ensure normal operation of gas engine. The Third step is power generating in gas engine. The high temperature exhaust gas may be reused by waste heat boiler to generate steam or hot water for civil or industrial use). Steam turbine may also be considered to make a gas-steam combined cycle power plant, which will increase the total efficiency.
This technology uses thermochemistry conversion method. With company independent R&D technology, coal can be converted into electricity, heating or charcoal. Moreover, the coal can be turned into wealth and can be made full use of.
The basic principle of coal gasification power generation system is to convert the different types coal into gas, and use the combustible gas to drive gas generating equipment for electricity. It can take full advantage of the equipment's compact-design and environmental-friendly features. Therefore, it is one of the most eco-friendly way for coal.
The process of coal gasification power generation includes three steps. The first step is coal gasification. The coal is converted into combustible gas. The second step is gas purification. The gas has impurities through gasification, including ash, tar, which should be removed with purification system in order to ensure the operation of gas power generator. The third step is gas power generation, which use gas engines(spark plug ignition type) for electricity generation, and the high temperature flue gas produced by the gas engine can heat boiler to get steam or hot water for residential or industrial use.
The coal gasification power generation system adopts modular design, which can be normally applied to power stations of 50-20000KW.
Typical coal quality index for gasifier
| Item | Technical requirements | Test method |
| Particle size, mm | bituminous coal:25~50,50~100,25~80 | GB/T189 |
| Block coal limit rate,% | ≤18.0 | MT/T1 |
| Inclusion rate, % | ≤3.0 | MT/T1 |
| Ash Ad, % | ≤18.00 | GB/T 212 |
| Coal ash melting softening temperature ST (°C) | >1250 | GB/T 219 |
| Total sulfur Std, % | ≤1.00 | GB/T 214 |
| Thermal stability TS-6,% | >60.0 | GB/T 1573 |
| Crush strength SS,% | >60.0 | GB/T15459 |
| Maximum thickness of the gel layer (1) Y, mm | ≤12.0 | GB/T 479 |
| Calorific value Qnet.ar, MJ/kg | bituminous coal:>21.00 | GB/T 213 |
Coal gasifier station
Gas Quality
- Gas temperature≤40ºC
- Gas pressure 2.5~10kPa
- Pressure change rate≤1kPa/min
- Calorific value ≥ 4.0MJ/Nm3
- Moisture content≤40g/Nm3, no free water
- Impurity content≤30mg/Nm3
- Impurity size≤5μm
- Tar content≤50mg/Nm3
- H2S≤50mg/Nm3
- Total sulfur≤100mg/Nm3
- NH3≤20mg/Nm3
- Cl≤50mg/Nm3
- H2≤50%
- O2≤1%
Gas Generator Specification
| Item | Technical specification | |||||
| Engine | Model | 6300D/M | 6300D/M-1 | 8300D/M-1 | 8300D/M-2 | 8300D/M-3 |
| Type | Inline, water cooled, four stroke, spark plug ignition | |||||
| Non-turbocharged | ||||||
| Cylinder number | 6 | 8 | ||||
| Cylinder diameter (mm) | 300 | |||||
| Rated speed(r/min) | 500 | 600 | 500 | 600 | 600 | |
| Rated power (kW) | 400 | 440 | 500 | 550 | 660 | |
| Rated thermal consumption(MJ/kW·h) | ≤11.0 | |||||
| Rotate direction (From flywheel) | Clockwise | |||||
| Start mode | Compressed air/motor start | |||||
| Exhaust temperature (ºC) | ≤600 | |||||
| Oil consumption(g/kW·h) | ≤0.8 | |||||
| Generator set | Type | 350GFM | 400GFM | 450GFM | 500GFM | 600GFM |
| Rated power(kW) | 350 | 400 | 450 | 500 | 600 | |
| Frequency(HZ) | 50 | |||||
| Voltage(V) | 400/6300/10500 | |||||
| Current(A) | 631/40/24 | 722/46/28 | 812/52/31 | 902/57/34 | 1083/69/41 | |
| Power factor (COSΦ) | 0.8 (Lagging) | |||||
| Phase and connecting | 3phases 4wires /3phases 3wires | |||||
| Dimension (L×W×H) (mm) | 5800×1600×2900 | 6400×1600×2900 | ||||
| Weight(kg) | 18000 | 22000 | ||||
Why Chosse Zichai product?
1. Development and manufacturing internal combustion engine since 1970
2. Factory area over 330000m2 & over 2200 employees
3. Highly versatile power generator with ability to handle more than 20 different gases
4. More than 200 employees dedicated to developing and improving power generator for various gas.
5. More than 1000 systems installed in over 20 countries using a variety of gases.
6. More than 50 people in the Customer Service Department making the Organization very Customer Responsive.
FAQ1.Are you a trading company or manufacture?
Manufacture with factory.
2.What kinds of gas generator set do you produce?
It covers for all kinds of gas produced in agriculture and industry, including biomass gas, biogas, natural gas, coal mine gas, coke oven gas, semi-coke gas and syngas, as well as related gas produce equipment.
3.What is your delivery time?
Normally within 60days, it depends on the configuration and quantity, please confirm with us before order.
4.What is your payment terms?
T/T or L/C.
5.How do you pack products?
Standard export packaging. Equipment packing with plastic bag, and with new solid wooden box, suitable for long-distance sea transportation, moisture-proof, earthquake, rust-proof and anti-brutal handling.
6.What is your available port of shipment?
Normally Qingdao port, other ports available according to customers' requirement.